Application classification 编辑

The Citrix SD-WAN appliances perform deep packet inspection (DPI) to identify and classify applications using the following techniques:

  • DPI library classification
  • Citrix-proprietary Independent Computing Architecture (ICA) classification
  • Application vendor APIs (for example Microsoft REST APIs for Office 365)
  • Domain name based application classification

DPI library classification

The Deep Packet Inspection (DPI) library recognizes thousands of commercial applications. It enables real-time discovery and classification of applications. Using the DPI technology, the SD-WAN appliance analyses the incoming packets and classifies the traffic as belonging to a particular application or application family. Application classification for each connection takes a few packets.

To enable DPI library classification, in the Configuration Editor, navigate to Global > Applications > DPI Settings and select the Enable Deep Packet Inspection check box.

ICA classification

Citrix SD-WAN appliances can also identify and classify Citrix HDX traffic for virtual apps and desktops. Citrix SD-WAN recognizes the following variations of the ICA protocol:

  • ICA
  • ICA-CGP
  • Single Stream ICA (SSI)
  • Multi-Stream ICA (MSI)
  • ICA over TCP
  • ICA over UDP/EDT
  • ICA over non-standard ports (including Multi-Port ICA)
  • HDX Adaptive Transport
  • ICA over WebSocket (used by HTML5 Receiver)

Note

Classification of ICA traffic delivered over SSL/TLS or DTLS is not supported in SD-WAN Standard Edition but is supported in SD-WAN Premium Edition and SD-WAN WANOP Edition.

Classification of network traffic is done during initial connections or flow establishment. Therefore, pre-existing connections are not classified as ICA. Classification of connections is also lost when the connection table is cleared manually.

Framehawk traffic and Audio-over-UDP/RTP are not classified as HDX applications. They are reported as either “UDP” or “Unknown Protocol.”

Since release 10 version 1, the SD-WAN appliance can differentiate each ICA data stream in multi-stream ICA even in a single-port configuration. Each ICA stream is classified as a separate application with its own default QoS class for prioritization.

  • For Multi-Stream ICA functionality to work properly, you must have SD-WAN Standard Edition 10.1 or above, or SD-WAN Premium Edition.

  • For HDX user based reports to be shown on SDWAN-Center, you must have SD-WAN Standard Edition or Premium Edition 11.0 or above.

Minimum software requirements for HDX information virtual channel:

  • A Current Release of Citrix Virtual Apps and Desktops (formerly XenApp and XenDesktop), since the prerequisite functionality was introduced in XenApp and XenDesktop 7.17 and is not included in the 7.15 Long-Term Service Release.

  • A version of the Citrix Workspace app (or its predecessor, Citrix Receiver) that supports multi-stream ICA and the HDX Insights information virtual channel, CTXNSAP. Look for HDX Insight with NSAP VC and Multiport/Multi-stream ICA in the Citrix Workspace app Feature Matrix. See the currently supported release versions at HDX Insights.

  • From 11.2 release onwards, packet duplication is now enabled by default for HDX real-time traffic when multi-stream ICA is in use.

Once classified, the ICA application can be used in application rules and to view application statistics similar to other classified applications.

There are five default application rules for ICA applications one each for the following priority tags:

  • Independent Computing Architecture (Citrix)(ICA)
  • ICA Real-time (ica_priority_0)
  • ICA Interactive (ica_priority_1)
  • ICA Bulk-Transfer (ica_prority_2)
  • ICA Background(ica_priority_3)

For more information, see Rules by Application Name

If you are running a combination of software that does not support Multi-Stream ICA over a single port, then to perform QoS you must configure multiple ports, one for each ICA stream. To classify HDX on non-standard ports as configured in XA/XD server policy, you must add those ports in ICA port configurations. Also, to match traffic on those ports to valid IP rules, you must update the ICA IP rules.

In the ICA IP and port list you can specify non-standard ports used in XA/XD policy to process for HDX classification. IP address is used to further restrict the ports to a specific destination. Use ‘*’ for port destined to any IP address. IP address with combination of SSL port is also used to indicate that the traffic is likely ICA even though the traffic is not finally classified as ICA. This indication is used to send L4 AppFlow records to support multi-hop reports in Citrix Application Delivery Management.

To enable ICA based classification, in the Configuration Editor, navigate to Global > Applications > DPI Settings and select the Enable Deep Packet Inspection for Citrix ICA Applications check box.

Application vendor API based classification

Citrix SD-WAN supports the following application vendor API based classification:

Domain name based application classification

The DPI classification engine is enhanced to classify applications based on the domain name and patterns. After the DNS forwarder intercepts and parses the DNS requests, the DPI engine uses the IP classifier to perform first packet classification. Further DPI library and ICA classification are done and the domain name based application ID is appended.

The Domain name based application feature allows you to group several domain names and treat it as a single application. Making it easier to apply firewall, application steering, QoS, and other rules. A maximum of 64 domain name based applications can be configured.

To define domain name based applications, in the Configuration Editor, navigate to Global > Applications > Domain Name Based Applications. Enter an application name and add the required domain names or patterns. You can either enter the full domain name or use wild cards at the beginning. The following domain name formats are allowed:

  • example.com
  • *.example.com

Domain name based applications

The classified domain name based applications are used in configuring the following:

Note

From 11.4.2 release onwards, the Domain name-based applications support configurable ports and protocol in Citrix SD-WAN Orchestrator service. For more information, see Domains and applications.

Limitations

  • If there are no DNS request/response corresponding to a domain name based application, the DPI engine does not classify the domain name based application and hence does not apply the application rules corresponding to the domain name based application.
  • If an Application Object is created such that the port range includes port 80 and/or port 443, with a specific IP address match type that corresponds to a domain name based application, the DPI engine does not classify the domain name based application.
  • If explicit web proxies are configured, you have to add all the domain name patterns to the PAC file, to ensure that the DNS response does not always return the same IP address.
  • The domain name based application classifications are reset on configuration upgrade. Reclassification happens based on pre 11.0.2 release classification techniques such as DPI library classification, ICA classification and Vendor application APIs based classification.
  • The application signatures learned (destination IP addresses) by domain name based application classification are reset on configuration update.
  • Only the standard DNS queries and their responses are processed.
  • AAAA records or IPv6 records are not supported.
  • DNS response records split over multiple packets are not processed. Only DNS responses in a single packet are processed.
  • DNS over TCP is not supported.
  • Only top-level domains are supported as domain name patterns.

Classifying encrypted traffic

Citrix SD-WAN appliance detects and reports encrypted traffic, as part of application reporting, in the following two methods:

  • For HTTPS traffic, the DPI engine inspects the SSL certificate to read the common name, which carries the name of the service (for example - Facebook, Twitter). Depending on the application architecture only one certificate might be used for several service types (for example - email, news, and so on). If different services use different certificates, the DPI engine would be able to differentiate between services.
  • For applications that use their own encryption protocol, the DPI engine looks for binary patterns in the flows for instance in case of Skype the DPI engine looks for a binary pattern inside the certificate and determines the application.

To configure application classification settings:

  1. In the Configuration Editor, click Global > Applications > Settings.

    Application settings

    Note

    If you add extra ICA port for multiport deployment, these ports must be added in Wan optimization application classifiers. Otherwise the traffic on the three extra ports will not forwarded to WANOP. Only the default 2598 port is forwarded if ICA is configured to optimize.

    WANOP application classifierg)

  2. Select Enable Deep Packet Inspection. This enables application classification on the appliance. You can, view, and monitor application statistics on the SD-WAN Center. For more information, see Application report.

    Note

    By default, Enable Deep Packet Inspection collects statistics for classified data.

  3. Select Enable Deep Packet Inspection for Citrix ICA Applications. This enables classification of Citrix ICA applications and collects statistics for user, sessions, and flow counts. Without this option enabled, some of the flavor of HDX traffic might still be classified and QoE calculated but statistics on SD-WAN center is not available. You can, view, and monitor ICA application statistics on the SD-WAN Center. This option is enabled by default. For more information, see HDX Reports.

  4. Select Enable HDX User Reporting to generate newly added user based reports (HDX Summary, HDX User Sessions, and HDX Apps) and these reports are available in SD-WAN Center. This is not applicable for the HDX Site Stats report. This option is available at the global and site level similar to enable DPI option. To Enable HDX User Reporting at site level, in the Configuration Editor, click Connections > Applications.

    Enable HDX reporting

  5. In DPI ICA Port, specify non-standard ports used in XA/XD policy to process for HDX classification. Do not include standard port numbers 2598 or 1494 in this list, as these are already included internally.

  6. In DPI ICA IP, specify the IP address to be used to further restrict the ports to the specific destination.

    Note

    Use ‘*’ for port destined to any IP address.

  7. Click Apply

You can configure application classification settings at each site individually. Click Connections, select a site and click Applications Settings. You can also choose to use the global application settings.

Search applications

You can search for an application to determine the application family name. A brief description of the application is also provided.

To search for an application:

  1. In the Configuration Editor, click Global > Applications> Search.

  2. In the Search field type, the name of the application and click enter.

    A brief description of the Application and the Application Family name appears.

    Application search

The following features use the application as a match type:

Note

For information on applications that the SD-WAN appliance can identify using Deep Packet Inspection, see Application Signature Library.

Application Objects

Application objects enable you to group different types of match criteria into a single object that can be used in firewall policies and application steering. IP Protocol, Application, and Application Family are the available match types.

The following features use the application object as a match type:

To create an application object:

  1. In the Configuration Editor, click Global > Applications > Application Objects.

  2. Click Add and, in the Name field, enter a name for the object.

    Application objects

  3. Select Enable Reporting to enable viewing custom application reports in Citrix SD-WAN Center. For more information see, Application Report.

  4. In the Priority field, enter the priority of the application object. When the incoming packets match two or more application object definitions, the application object with the highest priority is applied.

  5. Click + in the Application Match Criteria section.

  6. Select one of the following match types:

    • IP Protocol: Specify the protocol, network IP address, port number, and, DSCP tag.
    • Application: Specify the application name, network IP address, port number, and, DSCP tag.
    • Application Family: Select an application family and specify the network IP address, port number, and, DSCP tag.
  7. Click + to add more application match criteria.

  8. Click Add.

Using Application Classification with a Firewall

The classification of traffic as applications, application families or domain names enables you to use the application, application families, and application objects as match types to filter traffic and apply firewall policy and rules. It applies for all Pre, Post, and local policies. For more information about firewall, see Stateful Firewall and NAT Support.

Application classification in firewall

Viewing Application Classification

After enabling application classification, you can view the application name and application family details in the following reports:

  • Firewall connection Statistics

  • Flows information

  • Application statistics

Firewall connection statistics

In the Configuration Editor, navigate to Monitoring > Firewall. Under Connections section, the Application and Family columns list the applications and its associated family.

Firewall connections with application classification

If you do not enable application classification, the Application and Family columns do not show any data.

Firewall connections without application classification

Flows Information

In the Configuration Editor, navigate to Monitoring > Flows. Under Flows Data section, the Application column lists the application details.

Flows information

Application statistics

In the Configuration Editor, navigate to Monitoring > Statistics. Under Application Statistics section, the Application column lists the application details.

Application statistics

Troubleshooting

After enabling application classification, you can view the reports under the Monitoring section and ensure that they show application details. For more information, see Viewing Application Classification.

If there is any unexpected behavior, collect the STS diagnostics bundle while the issue is being observed, and share it with the Citrix Support team.

The STS bundle can be created and downloaded using Configuration > System Maintenance > Diagnostics > Diagnostic Information.

如果你对这篇内容有疑问,欢迎到本站社区发帖提问 参与讨论,获取更多帮助,或者扫码二维码加入 Web 技术交流群。

扫码二维码加入Web技术交流群

发布评论

需要 登录 才能够评论, 你可以免费 注册 一个本站的账号。
列表为空,暂无数据

词条统计

浏览:81 次

字数:23320

最后编辑:7 年前

编辑次数:0 次

    我们使用 Cookies 和其他技术来定制您的体验包括您的登录状态等。通过阅读我们的 隐私政策 了解更多相关信息。 单击 接受 或继续使用网站,即表示您同意使用 Cookies 和您的相关数据。
    原文