brocade 48k交换机扩容端口板和路由板

发布于 2022-09-03 11:33:20 字数 11165 浏览 10 评论 9

1、准备工作，扩容前准备好扩容所需备件。
2块48口端口板，2块FR4-18i路由板，4个电源模块，防静电环，十字螺丝刀
---------------------------------------扩容前------------------------------------------------
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
  1    SW BLADE 36    ENABLED
  2    SW BLADE 36    ENABLED
  3    SW BLADE 36    ENABLED
  4    SW BLADE 36    ENABLED
  5    CP BLADE 16    ENABLED
  6    CP BLADE 16    ENABLED
  7    SW BLADE 36    ENABLED
  8    UNKNOWN          VACANT
  9    UNKNOWN          VACANT
10 UNKNOWN          VACANT
B48K:admin>
B48K:admin> psshow
Power Supply #1 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024956
Power Supply #2 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024962
Power Supply #3 is absent
Power Supply #4 is absent
B48K:admin>
---------------------------------------硬件扩容----------------------------------------------
1、由于要使用FR4-18i板，所以必须先扩容Power Supply 3,4。
2、扩容8号slot 48口端口板
3、扩容10号solot FR4-18i板
---------------------------------------扩容后------------------------------------------------
1、在线扩容2个电源模块后，登陆交换机查看信息
B48K:admin> psshow
Power Supply #1 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024956
Power Supply #2 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024962
Power Supply #3 is OK
DELTA DPS1001AB-1EM 23020000603 03 FL2L945DD14
Power Supply #4 is OK
DELTA DPS1001AB-1EM 23020000603 02 FL2L945DBDB
B48K:admin>
2、在线扩容48口端口板及路由板后
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
  1    SW BLADE 36    ENABLED
  2    SW BLADE 36    ENABLED
  3    SW BLADE 36    ENABLED
  4    SW BLADE 36    ENABLED
  5    CP BLADE 16    ENABLED
  6    CP BLADE 16    ENABLED
  7    SW BLADE 36    ENABLED
  8    SW BLADE 36    DIAG RUNNING POST1
  9    UNKNOWN          VACANT
10    AP BLADE 24    DIAG RUNNING POST2
B48K:admin>
此时可以看到板卡正在自动跑POST。使用switchshow会看到48口端口板端口状态如下：
80 8 0 015000 id 4G No_Light       Testing  Disabled
81 8 1 015100 id 4G No_Light       Testing  Disabled
82 8 2 015200 id 4G No_Light       Testing  Disabled
83 8 3 015300 id 4G No_Light       Testing  Disabled
84 8 4 015400 id 4G No_Light       Testing  Disabled
85 8 5 015500 id 4G No_Light       Testing  Disabled
3、待POST完成后，新扩容板状态正常
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
  1    SW BLADE 36    ENABLED
  2    SW BLADE 36    ENABLED
  3    SW BLADE 36    ENABLED
  4    SW BLADE 36    ENABLED
  5    CP BLADE 16    ENABLED
  6    CP BLADE 16    ENABLED
  7    SW BLADE 36    ENABLED
  8    SW BLADE 36    ENABLED
  9    UNKNOWN          VACANT
10    AP BLADE 24    ENABLED
B48K:admin>
   48口端口板POST时间大概在2个小时左右，FR4-18i板POST时间大概30分钟。
4、查看FR4-18i路由板firmware如下
   B48K:admin> firmwareshow
Slot Name    Appl    Primary/Secondary Versions             Status
------------------------------------------------------------------------
  5  CP0    FOS    v5.3.0c                               STANDBY
                           v5.3.0c
  6  CP1    FOS    v5.3.0c                               ACTIVE *
                           v5.3.0c
10  FR4-18i  FOS    v5.3.0c
                           v5.3.0c
B48K:admin>
在将FR4-18i路由板插入到交换机后，FR4-18i板卡会自动从CP板download firmware。在messages中会看到如下信息：
2010/05/27-00:16:42, [SULB-1021], 2765,, WARNING, SilkWorm48000, Firmware is being downloaded to the blade in slot 10.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:16:40, [BM-1002], 2764,, INFO, SilkWorm48000, Connection established between CP and blade in slot 10.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:15:46, [FW-1445], 2763,, INFO, B48K, Four power supplies are now required for 2X redundancy, Switch Status Policy values changed.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:15:42, [EM-1049], 2762,, INFO, SilkWorm48000, FRU Slot 10 insertion detected.
Type <CR> to continue, Q<CR> to stop:
5、新加的FR4-18i路由板需要到brocade网站申请license，否则看到该板卡端口为Disabled (Persistent)状态
112 10 0 017000 id N4 No_Light       Disabled (Persistent)
113 10 1 017100 id N4 No_Light       Disabled (Persistent)
114 10 2 017200 id N4 No_Light       Disabled (Persistent)
115 10 3 017300 id N4 No_Light       Disabled (Persistent)
116 10 4 017400 id N4 No_Light       Disabled (Persistent)
117 10 5 017500 id N4 No_Light       Disabled (Persistent)
6、license申请方法
登陆https://www.switchkeyactivation.com/slkInternet/brocade网站，brocade license是与交换机WWN/Serial Number所绑定的，需要和随机附带的license盘中的Transaction Key到上述网站申请。所以在申请前请反复好核对好交换机的WWN和Serial Number，避免申请错误。
7、将申请的license添加到交换机
B48K:admin> licenseadd "b9dQS9bQbScIeRTu"
adding license-key [b9dQS9bQbScIeRTu]
B48K:admin>
B48K:admin> licenseshow
bQeSzScRdecRfT03:
Web license
cSQbzdddezdTRc0j:
Zoning license
zSzQdSced0T0ReM:
Fabric license
b9dQS9bQbSeAeRTo:
Fabric Watch license
b9dQS9bQbSgAeRTq:
Performance Monitor license
b9dQS9bQbSkAeRTu:
Trunking license
b9dQS9bQbScIeRTu:
High-Performance Extension over FCIP/FC license
B48K:admin>
8、将FR4-18i端口从Disabled (Persistent)状态改为正常状态
B48K:admin> portcfgpersistentenable 10/0
B48K:admin>
更改后状态如下：
112 10 0 017000 id N4 No_Light