当前位置： 文江博客话题详情

WS2812中断功能的STM32F103 PWM带有计时器和DMA

发布于 2025-02-07 02:22:41 字数 13314 浏览 2 评论 0原文

我正在尝试使用定时器生成的PWM和一个圆形DMA缓冲区来制作自己的WS2812 LED驱动程序，以保存内存。我设法获得了正确的时间，但是，使用逻辑分析器查看信号，我注意到两个主要的事情出了问题：

  • 例如，当应该发送72位时，只发送27位。
  • 错误的数据是在有限的27位发送的，即使在有限的27位中也不适当。

这是否实际上与不断称为中断有关，我不确定。我猜这是问题，因为不是发送全部零件，我还试图在其中一个中断上切换一个gpio pin，结果是销钉始终保持不变，可能表明中断是连续称为的因此，PIN没有足够的时间打开。我不确定是否还有其他方法可以测试何时和在什么时间间隔内中断。

如果确实是连续称为中断的情况，那么问题是什么？据我所知，我正在使用适当的回调功能，并且初始化是按顺序进行的。但是，我发现的奇怪部分是，每当我评论DMA PWM停止功能时，它就会开始正确发送位，即正确的量和正确的订单。如果中断被称为连续，我认为这不会起作用，因为DMA缓冲区会因中断例程而继续改变，这会导致错误的输出。我将感谢任何提示或建议！这是代码：

main.c

#include "main.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "ws2812.h"
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/
 TIM_HandleTypeDef htim2;
DMA_HandleTypeDef hdma_tim2_ch1;

/* USER CODE BEGIN PV */
uint8_t fbuffer[NUM_LEDS*3];
/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_DMA_Init(void);
static void MX_TIM2_Init(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */
  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_TIM2_Init();
  /* USER CODE BEGIN 2 */
//  if(sbyte & (1 << 7)) lh = 65;
//  else lh = 25;
  fbuffer[0] = 255;
  fbuffer[1] = 0;
  fbuffer[2] = 0;
  fbuffer[3] = 0;
  fbuffer[4] = 0;
  fbuffer[5] = 0;
  fbuffer[6] = 0;
  fbuffer[7] = 255;
  fbuffer[8] = 0;
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    ws2812_show(fbuffer);
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  {
    Error_Handler();
  }
}

/**
  * @brief TIM2 Initialization Function
  * @param None
  * @retval None
  */
static void MX_TIM2_Init(void)
{

  /* USER CODE BEGIN TIM2_Init 0 */

  /* USER CODE END TIM2_Init 0 */

  TIM_ClockConfigTypeDef sClockSourceConfig = {0};
  TIM_MasterConfigTypeDef sMasterConfig = {0};
  TIM_OC_InitTypeDef sConfigOC = {0};

  /* USER CODE BEGIN TIM2_Init 1 */

  /* USER CODE END TIM2_Init 1 */
  htim2.Instance = TIM2;
  htim2.Init.Prescaler = 0;
  htim2.Init.CounterMode = TIM_COUNTERMODE_UP;
  htim2.Init.Period = 89;
  htim2.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
  htim2.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE;
  if (HAL_TIM_Base_Init(&htim2) != HAL_OK)
  {
    Error_Handler();
  }
  sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
  if (HAL_TIM_ConfigClockSource(&htim2, &sClockSourceConfig) != HAL_OK)
  {
    Error_Handler();
  }
  if (HAL_TIM_PWM_Init(&htim2) != HAL_OK)
  {
    Error_Handler();
  }
  sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
  sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
  if (HAL_TIMEx_MasterConfigSynchronization(&htim2, &sMasterConfig) != HAL_OK)
  {
    Error_Handler();
  }
  sConfigOC.OCMode = TIM_OCMODE_PWM1;
  sConfigOC.Pulse = 0;
  sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
  if (HAL_TIM_PWM_ConfigChannel(&htim2, &sConfigOC, TIM_CHANNEL_1) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN TIM2_Init 2 */

  /* USER CODE END TIM2_Init 2 */
  HAL_TIM_MspPostInit(&htim2);

}

/**
  * Enable DMA controller clock
  */
static void MX_DMA_Init(void)
{

  /* DMA controller clock enable */
  __HAL_RCC_DMA1_CLK_ENABLE();

  /* DMA interrupt init */
  /* DMA1_Channel5_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(DMA1_Channel5_IRQn, 0, 0);
  HAL_NVIC_EnableIRQ(DMA1_Channel5_IRQn);

}

/**
  * @brief GPIO Initialization Function
  * @param None
  * @retval None
  */
static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOD_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0, GPIO_PIN_RESET);

  /*Configure GPIO pin : PA0 */
  GPIO_InitStruct.Pin = GPIO_PIN_0;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

}

ws2812.c

#include "main.h"
#include "ws2812.h"

extern TIM_HandleTypeDef htim2;
extern DMA_HandleTypeDef hdma_tim2_ch1;
extern uint8_t fbuffer[NUM_LEDS*3];

uint16_t indby = 3;
uint32_t bcolors = 0;
uint8_t circbuffer[24] = {0};

uint8_t rd_flag = 0;
uint8_t in_flag = 0;

// Interrupt for when half of the DMA buffer is reached.
void HAL_TIM_PWM_PulseFinishedHalfCpltCallback(TIM_HandleTypeDef *htim)
{
    if (htim->Instance == htim2.Instance) {
        if(indby < NUM_LEDS*3) {
            // Fill the first half of the DMA buffer
            bcolors = (fbuffer[indby+1] << 16) | (fbuffer[indby] << 8) | fbuffer[indby+2];
            for(uint8_t i = 23; i > 11; i--) {
                if(bcolors & (1<<i)) circbuffer[23-i] = HT;
                else circbuffer[23-i] = LT;
            }
        }
    }
}

// Interrupt for when all of the DMA buffer is passed.
void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim)
{
    if (htim->Instance == htim2.Instance) {
        if(indby < NUM_LEDS*3) {
            // Set the latter half of the DMA buffer
            for(uint8_t i = 11; i > 0; i--) {
                if(bcolors & (1<<i)) circbuffer[23-i] = HT;
                else circbuffer[23-i] = LT;
            }
            if(bcolors & (1<<0)) circbuffer[23] = HT;
            else circbuffer[23] = LT;
            indby += 3;
            //HAL_GPIO_TogglePin(GPIOA, GPIO_PIN_0);
        }
        // Stop PWM if last LED bit reached.
        else {
            HAL_TIM_PWM_Stop_DMA(&htim2, TIM_CHANNEL_1);
            rd_flag = 0;
        }
    }
}

uint8_t ws2812_show(uint8_t fbuffer[])
{
    // State machine like switch to make sure the functions runs properly on
    // consecutive calls
    switch(0 ^ in_flag ^ (rd_flag<<1)) {
    // Initialization state
    case 0:
        in_flag = 1;
        rd_flag = 1;
        bcolors = (fbuffer[1] << 16) | (fbuffer[0] << 8) | fbuffer[2];
        for(uint8_t i = 23; i > 0; i--) {
            if(bcolors & (1<<i)) circbuffer[23-i] = HT;
            else circbuffer[23-i] = LT;
        }
        if(bcolors & (1<<0)) circbuffer[23] = HT;
        else circbuffer[23] = LT;
        HAL_TIM_PWM_Start_DMA(&htim2, TIM_CHANNEL_1, (uint32_t *)circbuffer, 24);
        return 0;
        break;
    // Running state
    case 3:
        return 0;
        break;
    // Finished state
    case 1:
        in_flag = 0;
        return 1;
        break;
    // Something is up state
    case 2:
        rd_flag = 0;
        return 0;
        break;
    default:
        return 0;
    }
}

stm32f1xx_hal_msp.c

#include "main.h"
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */
extern DMA_HandleTypeDef hdma_tim2_ch1;

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN TD */

/* USER CODE END TD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN Define */

/* USER CODE END Define */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN Macro */

/* USER CODE END Macro */

/* Private variables ---------------------------------------------------------*/
/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* External functions --------------------------------------------------------*/
/* USER CODE BEGIN ExternalFunctions */

/* USER CODE END ExternalFunctions */

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

void HAL_TIM_MspPostInit(TIM_HandleTypeDef *htim);
                    /**
  * Initializes the Global MSP.
  */
void HAL_MspInit(void)
{
  /* USER CODE BEGIN MspInit 0 */

  /* USER CODE END MspInit 0 */

  __HAL_RCC_AFIO_CLK_ENABLE();
  __HAL_RCC_PWR_CLK_ENABLE();

  /* System interrupt init*/

  /** NOJTAG: JTAG-DP Disabled and SW-DP Enabled
  */
  __HAL_AFIO_REMAP_SWJ_NOJTAG();

  /* USER CODE BEGIN MspInit 1 */

  /* USER CODE END MspInit 1 */
}

/**
* @brief TIM_Base MSP Initialization
* This function configures the hardware resources used in this example
* @param htim_base: TIM_Base handle pointer
* @retval None
*/
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
  if(htim_base->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspInit 0 */

  /* USER CODE END TIM2_MspInit 0 */
    /* Peripheral clock enable */
    __HAL_RCC_TIM2_CLK_ENABLE();

    /* TIM2 DMA Init */
    /* TIM2_CH1 Init */
    hdma_tim2_ch1.Instance = DMA1_Channel5;
    hdma_tim2_ch1.Init.Direction = DMA_MEMORY_TO_PERIPH;
    hdma_tim2_ch1.Init.PeriphInc = DMA_PINC_DISABLE;
    hdma_tim2_ch1.Init.MemInc = DMA_MINC_ENABLE;
    hdma_tim2_ch1.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;
    hdma_tim2_ch1.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
    hdma_tim2_ch1.Init.Mode = DMA_CIRCULAR;
    hdma_tim2_ch1.Init.Priority = DMA_PRIORITY_LOW;
    if (HAL_DMA_Init(&hdma_tim2_ch1) != HAL_OK)
    {
      Error_Handler();
    }

    __HAL_LINKDMA(htim_base,hdma[TIM_DMA_ID_CC1],hdma_tim2_ch1);

    /* TIM2 interrupt Init */
    HAL_NVIC_SetPriority(TIM2_IRQn, 0, 0);
    HAL_NVIC_EnableIRQ(TIM2_IRQn);
  /* USER CODE BEGIN TIM2_MspInit 1 */

  /* USER CODE END TIM2_MspInit 1 */
  }

}

void HAL_TIM_MspPostInit(TIM_HandleTypeDef* htim)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  if(htim->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspPostInit 0 */

  /* USER CODE END TIM2_MspPostInit 0 */

    __HAL_RCC_GPIOA_CLK_ENABLE();
    /**TIM2 GPIO Configuration
    PA15     ------> TIM2_CH1
    */
    GPIO_InitStruct.Pin = GPIO_PIN_15;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

    __HAL_AFIO_REMAP_TIM2_PARTIAL_1();

  /* USER CODE BEGIN TIM2_MspPostInit 1 */

  /* USER CODE END TIM2_MspPostInit 1 */
  }

}
/**
* @brief TIM_Base MSP De-Initialization
* This function freeze the hardware resources used in this example
* @param htim_base: TIM_Base handle pointer
* @retval None
*/
void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
{
  if(htim_base->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspDeInit 0 */

  /* USER CODE END TIM2_MspDeInit 0 */
    /* Peripheral clock disable */
    __HAL_RCC_TIM2_CLK_DISABLE();

    /* TIM2 DMA DeInit */
    HAL_DMA_DeInit(htim_base->hdma[TIM_DMA_ID_CC1]);

    /* TIM2 interrupt DeInit */
    HAL_NVIC_DisableIRQ(TIM2_IRQn);
  /* USER CODE BEGIN TIM2_MspDeInit 1 */

  /* USER CODE END TIM2_MspDeInit 1 */
  }

}

，如果需要，我以后可以提供逻辑分析仪波形。

原文

I am trying to make my own driver for WS2812 LEDs with a timer generated PWM and a circular DMA buffer for conserving memory. I managed to get the right timings, however, looking at the signal with a logic analyzer, I notice that two main things go wrong:

  • When, for example, 72 bits are supposed to be sent, only 27 bits are sent.
  • Wrong data is sent and not in appropriate order even in the limited 27 bits.

Whether this is actually related to interrupts being constantly called I am not entirely sure. I am guessing this is the issue because not the full amount of bits is sent and I also tried to toggle a GPIO pin on either one of the interrupts and the result was that the pin always stayed off, possibly indicating that the interrupt is continuously called and so the pin does not have enough time to switch on. I am not sure if there are any other ways to test when and in what time intervals the interrupts occur.

If this is indeed the case of continuously called interrupts, what could be the issue? As far as I can tell I am using appropriate callback functions and my initializations are in order. However, the weird part that I found was that whenever I comment out the DMA PWM stop function, it starts sending out bits correctly, that is, right amount and right order. If the interrupts were called continuosly, I don't think this would work, because the DMA buffer would keep getting changed by the interrupt routines, which should cause erroneous output. I would be thankful for any tips or advice! Here's the code:

main.c

#include "main.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "ws2812.h"
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/
 TIM_HandleTypeDef htim2;
DMA_HandleTypeDef hdma_tim2_ch1;

/* USER CODE BEGIN PV */
uint8_t fbuffer[NUM_LEDS*3];
/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_DMA_Init(void);
static void MX_TIM2_Init(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */
  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_TIM2_Init();
  /* USER CODE BEGIN 2 */
//  if(sbyte & (1 << 7)) lh = 65;
//  else lh = 25;
  fbuffer[0] = 255;
  fbuffer[1] = 0;
  fbuffer[2] = 0;
  fbuffer[3] = 0;
  fbuffer[4] = 0;
  fbuffer[5] = 0;
  fbuffer[6] = 0;
  fbuffer[7] = 255;
  fbuffer[8] = 0;
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    ws2812_show(fbuffer);
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  {
    Error_Handler();
  }
}

/**
  * @brief TIM2 Initialization Function
  * @param None
  * @retval None
  */
static void MX_TIM2_Init(void)
{

  /* USER CODE BEGIN TIM2_Init 0 */

  /* USER CODE END TIM2_Init 0 */

  TIM_ClockConfigTypeDef sClockSourceConfig = {0};
  TIM_MasterConfigTypeDef sMasterConfig = {0};
  TIM_OC_InitTypeDef sConfigOC = {0};

  /* USER CODE BEGIN TIM2_Init 1 */

  /* USER CODE END TIM2_Init 1 */
  htim2.Instance = TIM2;
  htim2.Init.Prescaler = 0;
  htim2.Init.CounterMode = TIM_COUNTERMODE_UP;
  htim2.Init.Period = 89;
  htim2.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
  htim2.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE;
  if (HAL_TIM_Base_Init(&htim2) != HAL_OK)
  {
    Error_Handler();
  }
  sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
  if (HAL_TIM_ConfigClockSource(&htim2, &sClockSourceConfig) != HAL_OK)
  {
    Error_Handler();
  }
  if (HAL_TIM_PWM_Init(&htim2) != HAL_OK)
  {
    Error_Handler();
  }
  sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
  sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
  if (HAL_TIMEx_MasterConfigSynchronization(&htim2, &sMasterConfig) != HAL_OK)
  {
    Error_Handler();
  }
  sConfigOC.OCMode = TIM_OCMODE_PWM1;
  sConfigOC.Pulse = 0;
  sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
  sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
  if (HAL_TIM_PWM_ConfigChannel(&htim2, &sConfigOC, TIM_CHANNEL_1) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN TIM2_Init 2 */

  /* USER CODE END TIM2_Init 2 */
  HAL_TIM_MspPostInit(&htim2);

}

/**
  * Enable DMA controller clock
  */
static void MX_DMA_Init(void)
{

  /* DMA controller clock enable */
  __HAL_RCC_DMA1_CLK_ENABLE();

  /* DMA interrupt init */
  /* DMA1_Channel5_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(DMA1_Channel5_IRQn, 0, 0);
  HAL_NVIC_EnableIRQ(DMA1_Channel5_IRQn);

}

/**
  * @brief GPIO Initialization Function
  * @param None
  * @retval None
  */
static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOD_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0, GPIO_PIN_RESET);

  /*Configure GPIO pin : PA0 */
  GPIO_InitStruct.Pin = GPIO_PIN_0;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

}

ws2812.c

#include "main.h"
#include "ws2812.h"

extern TIM_HandleTypeDef htim2;
extern DMA_HandleTypeDef hdma_tim2_ch1;
extern uint8_t fbuffer[NUM_LEDS*3];

uint16_t indby = 3;
uint32_t bcolors = 0;
uint8_t circbuffer[24] = {0};

uint8_t rd_flag = 0;
uint8_t in_flag = 0;

// Interrupt for when half of the DMA buffer is reached.
void HAL_TIM_PWM_PulseFinishedHalfCpltCallback(TIM_HandleTypeDef *htim)
{
    if (htim->Instance == htim2.Instance) {
        if(indby < NUM_LEDS*3) {
            // Fill the first half of the DMA buffer
            bcolors = (fbuffer[indby+1] << 16) | (fbuffer[indby] << 8) | fbuffer[indby+2];
            for(uint8_t i = 23; i > 11; i--) {
                if(bcolors & (1<<i)) circbuffer[23-i] = HT;
                else circbuffer[23-i] = LT;
            }
        }
    }
}

// Interrupt for when all of the DMA buffer is passed.
void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim)
{
    if (htim->Instance == htim2.Instance) {
        if(indby < NUM_LEDS*3) {
            // Set the latter half of the DMA buffer
            for(uint8_t i = 11; i > 0; i--) {
                if(bcolors & (1<<i)) circbuffer[23-i] = HT;
                else circbuffer[23-i] = LT;
            }
            if(bcolors & (1<<0)) circbuffer[23] = HT;
            else circbuffer[23] = LT;
            indby += 3;
            //HAL_GPIO_TogglePin(GPIOA, GPIO_PIN_0);
        }
        // Stop PWM if last LED bit reached.
        else {
            HAL_TIM_PWM_Stop_DMA(&htim2, TIM_CHANNEL_1);
            rd_flag = 0;
        }
    }
}

uint8_t ws2812_show(uint8_t fbuffer[])
{
    // State machine like switch to make sure the functions runs properly on
    // consecutive calls
    switch(0 ^ in_flag ^ (rd_flag<<1)) {
    // Initialization state
    case 0:
        in_flag = 1;
        rd_flag = 1;
        bcolors = (fbuffer[1] << 16) | (fbuffer[0] << 8) | fbuffer[2];
        for(uint8_t i = 23; i > 0; i--) {
            if(bcolors & (1<<i)) circbuffer[23-i] = HT;
            else circbuffer[23-i] = LT;
        }
        if(bcolors & (1<<0)) circbuffer[23] = HT;
        else circbuffer[23] = LT;
        HAL_TIM_PWM_Start_DMA(&htim2, TIM_CHANNEL_1, (uint32_t *)circbuffer, 24);
        return 0;
        break;
    // Running state
    case 3:
        return 0;
        break;
    // Finished state
    case 1:
        in_flag = 0;
        return 1;
        break;
    // Something is up state
    case 2:
        rd_flag = 0;
        return 0;
        break;
    default:
        return 0;
    }
}

stm32f1xx_hal_msp.c

#include "main.h"
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */
extern DMA_HandleTypeDef hdma_tim2_ch1;

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN TD */

/* USER CODE END TD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN Define */

/* USER CODE END Define */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN Macro */

/* USER CODE END Macro */

/* Private variables ---------------------------------------------------------*/
/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* External functions --------------------------------------------------------*/
/* USER CODE BEGIN ExternalFunctions */

/* USER CODE END ExternalFunctions */

/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

void HAL_TIM_MspPostInit(TIM_HandleTypeDef *htim);
                    /**
  * Initializes the Global MSP.
  */
void HAL_MspInit(void)
{
  /* USER CODE BEGIN MspInit 0 */

  /* USER CODE END MspInit 0 */

  __HAL_RCC_AFIO_CLK_ENABLE();
  __HAL_RCC_PWR_CLK_ENABLE();

  /* System interrupt init*/

  /** NOJTAG: JTAG-DP Disabled and SW-DP Enabled
  */
  __HAL_AFIO_REMAP_SWJ_NOJTAG();

  /* USER CODE BEGIN MspInit 1 */

  /* USER CODE END MspInit 1 */
}

/**
* @brief TIM_Base MSP Initialization
* This function configures the hardware resources used in this example
* @param htim_base: TIM_Base handle pointer
* @retval None
*/
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
  if(htim_base->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspInit 0 */

  /* USER CODE END TIM2_MspInit 0 */
    /* Peripheral clock enable */
    __HAL_RCC_TIM2_CLK_ENABLE();

    /* TIM2 DMA Init */
    /* TIM2_CH1 Init */
    hdma_tim2_ch1.Instance = DMA1_Channel5;
    hdma_tim2_ch1.Init.Direction = DMA_MEMORY_TO_PERIPH;
    hdma_tim2_ch1.Init.PeriphInc = DMA_PINC_DISABLE;
    hdma_tim2_ch1.Init.MemInc = DMA_MINC_ENABLE;
    hdma_tim2_ch1.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;
    hdma_tim2_ch1.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
    hdma_tim2_ch1.Init.Mode = DMA_CIRCULAR;
    hdma_tim2_ch1.Init.Priority = DMA_PRIORITY_LOW;
    if (HAL_DMA_Init(&hdma_tim2_ch1) != HAL_OK)
    {
      Error_Handler();
    }

    __HAL_LINKDMA(htim_base,hdma[TIM_DMA_ID_CC1],hdma_tim2_ch1);

    /* TIM2 interrupt Init */
    HAL_NVIC_SetPriority(TIM2_IRQn, 0, 0);
    HAL_NVIC_EnableIRQ(TIM2_IRQn);
  /* USER CODE BEGIN TIM2_MspInit 1 */

  /* USER CODE END TIM2_MspInit 1 */
  }

}

void HAL_TIM_MspPostInit(TIM_HandleTypeDef* htim)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};
  if(htim->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspPostInit 0 */

  /* USER CODE END TIM2_MspPostInit 0 */

    __HAL_RCC_GPIOA_CLK_ENABLE();
    /**TIM2 GPIO Configuration
    PA15     ------> TIM2_CH1
    */
    GPIO_InitStruct.Pin = GPIO_PIN_15;
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

    __HAL_AFIO_REMAP_TIM2_PARTIAL_1();

  /* USER CODE BEGIN TIM2_MspPostInit 1 */

  /* USER CODE END TIM2_MspPostInit 1 */
  }

}
/**
* @brief TIM_Base MSP De-Initialization
* This function freeze the hardware resources used in this example
* @param htim_base: TIM_Base handle pointer
* @retval None
*/
void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef* htim_base)
{
  if(htim_base->Instance==TIM2)
  {
  /* USER CODE BEGIN TIM2_MspDeInit 0 */

  /* USER CODE END TIM2_MspDeInit 0 */
    /* Peripheral clock disable */
    __HAL_RCC_TIM2_CLK_DISABLE();

    /* TIM2 DMA DeInit */
    HAL_DMA_DeInit(htim_base->hdma[TIM_DMA_ID_CC1]);

    /* TIM2 interrupt DeInit */
    HAL_NVIC_DisableIRQ(TIM2_IRQn);
  /* USER CODE BEGIN TIM2_MspDeInit 1 */

  /* USER CODE END TIM2_MspDeInit 1 */
  }

}

If need be, I can later provide the logic analyser waveforms.

如果你对这篇内容有疑问，欢迎到本站社区发帖提问 参与讨论，获取更多帮助，或者扫码二维码加入 Web 技术交流群。

扫码二维码加入Web技术交流群

发布评论

需要 登录 才能够评论， 你可以免费 注册 一个本站的账号。

评论（1）

李不 2025-02-14 02:22:41

从字面上看，忘了简单地重置字节计数变量indby。上这件教训非常仔细检查您的代码！

Literally forgot to simply reset the byte counting variable indby. Take this as a lesson to very carefully check your code!

回复 原文
~没有更多了~

关于作者

韶华倾负

暂无简介

文章
评论
27 人气
发私信

相关话题

更多

热门标签

操作系统 程序设计 IT运维 Linux系统管理 JavaScript 服务器应用 solaris C/C++ PHP Shell BSD Vue.js aix Oracle Python HTML 系统管理 HTML5 CSS 前端
更多

推荐作者

李珊平

文章 0 评论 0

Quxin

文章 0 评论 0

范无咎

文章 0 评论 0

github_ZOJ2N8YxBm

文章 0 评论 0

若言

文章 0 评论 0

南…巷孤猫

文章 0 评论 0

更多

友情链接

文江博客
    我们使用 Cookies 和其他技术来定制您的体验包括您的登录状态等。通过阅读我们的 隐私政策 了解更多相关信息。 单击 接受 或继续使用网站，即表示您同意使用 Cookies 和您的相关数据。
    原文