Zebra 标签打印机 TLP 2824 Plus 可打印 2 张标签并退出
我们拥有 Zebra TLP 2824-Z Plus 标签打印机 (ZLP)。我们最近购买了它，成功安装了驱动程序和软件，并成功校准（按住按钮呈稳定绿色，单闪然后双闪，然后释放按钮）。我们去了 Zebra 并检索了更新的驱动程序（经过认证）并安装了它们（仅供参考，已经尝试过使用和不使用这些驱动程序 - 没有它们将不会执行任何操作）。
通过 USB 安装的系统是 Windows XP Pro 32 位 SP3。
配置完成后，它将立即进行测试打印，然后让我们发送命令来送入标签。如果我们尝试打印配置或其他任何内容（包括打印实际标签），它会打印两个标签/页面，停止，然后闪烁红色。如果我们抬起顶部并将其放下，它会闪烁绿色，直到我们按下按钮。此时，它会送入约 2 至 3 英寸的标签，然后打印一张标签。该过程无限重复，直到我们卸载打印机。
不，清除文件并不能阻止它。硬重置不会阻止它。让它做其他事情的唯一方法就是卸载它并重新开始。
我们如何解决这个问题，以便我们可以获得配置或只是打印我们的标签？或者，更好的是，我们做错了什么以及我们如何做对？我们的最后一台打印机工作正常，只是他们停止制作我们在该打印机上使用的标签。
We have the Zebra TLP 2824-Z Plus label printer (ZLP). We recently purchased it, installed the driver and software successfully, and calibrated successfully (held button down at solid green, got single blink then double blink, and then released the button). We went to Zebra and retrieved the updated drivers (certified) and installed them (fyi have tried with and without these drivers - will do nothing without them).
The system it is installed on via USB is a Windows XP Pro 32-bit SP3.
Immediately after configuration, it will do a test print, and let us send the command to feed a label. If we try to print configuration or anything else, to include printing actual labels, it prints two labels/pages, stops, and then blinks red. If we lift the top off and put it down, it blinks green until we press the button. At that time, it will feed about 2 to 3 inches of labels and then print one label. The process repeats indefinitely until we uninstall the printer.
No, clearing the documents will not stop it. A hard reset will not stop it. The only way to get it to do anything else is to uninstall it and start all over again.
How do we fix this issue so we can get a configuration or just print our labels? Or, better yet, what are we doing wrong and how do we do it right? Our last printer worked fine with the exception that they stopped making the labels we used with that printer.
如果你对这篇内容有疑问，欢迎到本站社区发帖提问 参与讨论，获取更多帮助，或者扫码二维码加入 Web 技术交流群。
绑定邮箱获取回复消息
由于您还没有绑定你的真实邮箱，如果其他用户或者作者回复了您的评论，将不能在第一时间通知您！
发布评论
评论（2）
驱动器根据打印机首选项中的设置发送打印机的初始化序列。例如，如果您的打印机首选项表明打印机处于热敏模式而不是热敏模式，则驱动程序将发送命令以将打印机设置为热敏模式（色带）。如果您的打印机采用热敏打印，并且没有实际安装色带，则打印机会认为它处于没有色带的错误模式。这可能会导致您所看到的问题。
确保您的打印机首选项与打印机的配置相符，或禁用驱动程序中的初始化序列
The drive sends down an initialization sequence for the printer based on the settings in the Printer Preferences. If, for example, your Printer preferences say that the printer is Thermal mode instead of direct thermal, the driver will send down the command to set the printer to Thermal mode (Ribbon). If your printer is printing Direct Thermal, and has no ribbon physically installed, the printer will think it is in an error mode with no ribbon. This could cause the issue you are seeing.
Ensure that your Printer Preferences are accurate to your printer's configuration, or disable the initialization sequence in the driver
是的。只需确保所有设置均正确即可。
Yes. Just make sure all the settings are correct.