求助，开发板 kernel panic了

发布于 2022-10-15 06:58:29 字数 6445 浏览 31 评论 0

Starting kernel ...

Uncompressing Linux.................................................................................................
Linux version 2.6.29.4uplooking (root@zhang.uplooking.com) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #24 F1
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: FriendlyARM Mini2440 development board
Memory policy: ECC disabled, Data cache writeback
!!!!!static io remap!!!!!
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/nfs rw nfsroot=192.168.1.3:/nfsroot ip=192.168.1.8 console=ttySAC0,115200 mM
irq: clearing pending ext status 00080000
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61724KB available (2728K code, 298K data, 116K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 201.93 BogoMIPS (lpj=504832)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 296 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 204
TCP reno registered
NET: Registered protocol family 1
yaffs Jan 21 2011 16:55:42 Installing.
msgmni has been set to 120
io scheduler noop registered (default)
s3c2410-lcd s3c2410-lcd: failed to get memory region
s3c2410-lcd: probe of s3c2410-lcd failed with error -2
backlight    initialized
leds initialized
buttons initialized
pwm    initialized
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
loop: module loaded
dm9000 Ethernet Driver, V1.31
Now use the default MAC address: 08:90:90:90:90:90
eth0 (dm9000): not using net_device_ops yet
eth0: dm9000a at c480c000,c4810004 IRQ 51 MAC: 08:90:90:90:90:90 (friendly-arm)
Register cs8900 Ethernet Driver for qq2440.
cs8900: probbing for qq2440...
eth%d: incorrect signature 0x0201
Linux video capture interface: v2.00
initializing s3c2440 camera interface......
s3c2440 camif init done
Loading OV9650 driver.........
SCCB address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
SCCB address 0x60, manufacture ID 0xFFFF, expect 0x7FA2
No OV9650 found!!!
Driver 'sd' needs updating - please use bus_type methods
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 337 at 0x000002a20000
Bad eraseblock 686 at 0x0000055c0000
Bad eraseblock 1099 at 0x000008960000
Bad eraseblock 1379 at 0x00000ac60000
Bad eraseblock 1385 at 0x00000ad20000
Bad eraseblock 1451 at 0x00000b560000
Bad eraseblock 1631 at 0x00000cbe0000
Bad eraseblock 1665 at 0x00000d020000
Bad eraseblock 1884 at 0x00000eb80000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "supervivi"
0x000000100000-0x000000300000 : "Kernel"
0x000000300000-0x00000c300000 : "root"
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI UDA134X
No device for DAI s3c24xx-i2s
S3C24XX_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: UDA134X <-> s3c24xx-i2s mapping ok
ALSA device list:
  #0: S3C24XX_UDA134X (UDA134X)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
   device=eth0, addr=192.168.1.8, mask=255.255.255.0, gw=255.255.255.255,
   host=192.168.1.8, domain=, nis-domain=(none),
   bootserver=255.255.255.255, rootserver=192.168.1.3, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.3
Looking up port of RPC 100005/1 on 192.168.1.3
VFS: Mounted root (nfs filesystem) on device 0:10.
Freeing init memory: 116K
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.