HP 9000 J6000 怎么更改从显卡开机启动？

Question

本来有一台HP J6000 ,用超级终端OK，装好系统之后，还是没法从显卡开机显示，请问是什么问题，该怎么更改设置？
请各位大侠指点一下，谢谢！

Answer 1

sevice hand book下载地址:
http://h20000.www2.hp.com/bc/doc ... v37677/lpv37677.pdf

itrc 参考
http://forums11.itrc.hp.com/serv ... .do?threadId=194761

将显示器VGA接口接在工作站的VGA接口上，开机的时候，Num Lock灯亮后2秒按键盘上的TAB键，看是否有显示，最好是搞个能支持1600×1200以上分辨率的CRT显示器，系统默认最小的分辨率为1024*768@75HZ，一般的液晶显示器可能不行。如果不行的话，参考service hand book 110页后面的命令对显示器的参数进行修改。

注意，刚才在ITRC上看到，必须外接USB 键盘显示器才会有输出的，如果可能也接上USB鼠标，2个USB接口在工作站后面网线接口的右边。
Keyboard
The standard USB keyboard (Product Number A4983-604xx – the actual suffix number
depends on the localized version of the keyboard) with the J6000 workstations is a 104-key
input device. It is a PC-104 compatible keyboard.

Mouse
The USB mouse is either a scroll wheel type mouse (Product Number A4983-60101) where
the scroll wheel also serves as the middle button, or a true three-button type mouse
(Product Number A4983-60111).

The two Universal Serial Bus (USB) connectors support only the HP keyboard, mouse, or
hub (D6804A). You can connect the HP keyboard, mouse, or hub in either of the USB
connectors.
The USB mouse and keyboard were shipped with your system unit. The HP hub can be
ordered separately. Note that you should consult the documentation that accompanies
each input device for specific information concerning its use.
For more information on the Universal Serial Bus, use your browser to access the following
URL: http://www.usb.org.

有可能要重新设置console的path:
boot 到BCH－－configuration－－monitor graphics_path type(显示系统安装的显卡)－－path console graphics(1) (显示器连接的那块显卡)

由于没有机器，我没办法给你测试，折腾几天，把手册看透，到ITRC，google上搜索应该能解决问题的。

搞定了，记得分享下过程。

Good luck!

------------------------------------------------------------------------------------------------------------------------------------------
Setting the Monitor Type at Power On
If you replace a workstation’s monitor with a different monitor type, and do not set the
workstation’s graphics parameters by using the monitor command before doing so, you
may need to perform the following if your screen is blank.
Cycle the power to the workstation. Wait 2 seconds after the Num Lock light flashes near
the end of the boot sequence, and then press [Tab] to initiate the automatic monitor
selection process. If the screen remains blank after two minutes, however, see the
“Troubleshooting Monitor Problems” subsection on the next page.
NOTE It takes approximately one minute after powering on the workstation before
the Num Lock light flashes.
The system cycles through the available monitor types one at a time. When you see a
message similar to the following, and it is the correct monitor type, select the monitor type
by pressing [Enter]:
MONITOR INFORMATION
Path Slot Head Type Size Freq Type Class
------------- --------- -------- ------------- ------------------ ------- ------- -------
GRAPHICS(1) 1 1 n nnnnxnnnn nnHz 8 PCI
Press [RETURN] to select this monitor type (type n of n types)
The system queries you to confirm your selection. Press Y (yes) to save this monitor type.
If you press any key other than Y, the following message is displayed:
Monitor type not saved.
At this point, the new monitor type is active, but not saved. Because you did not save the
monitor type, the next time you reboot the workstation the original monitor type will be
used.
Next, the following message is displayed:
To select a new Graphics Monitor Type press the <TAB> key now, otherwise
EXIT by entering any other key (or will time out in 15 seconds)...
To restart the monitor selection process, press [Tab].

Answer 2

没研究过这东东

Answer 3

谢谢

Answer 4

更具我玩hp的经验，你必须在启动的时候用串口登上去，在菜单中设置“console” 选项，一般有一个“p”，还有一个“s”
你设置以下就可以了！