Question

Note This list is auto-generated from the source code.

The AUX channels are only available on Pixhawk Boards (labeled with AUX OUT).

This page lists all supported airframes and types including
the motor assignment and numbering. The motors in green rotate clockwise,
the ones in blue counterclockwise.

Copter

Coaxial Helicopter

Common Outputs
MAIN1: Left swashplate servomotor, pitch axis MAIN2: Right swashplate servomotor, roll axis MAIN3: Upper rotor (CCW) MAIN4: Lower rotor (CW)

Name
Esky (Big) Lama v4	Maintainer: Emmanuel Roussel SYS_AUTOSTART = 15001

Dodecarotor cox

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 AUX1: motor 7 AUX2: motor 8 AUX3: motor 9 AUX4: motor 10 AUX5: motor 11 AUX6: motor 12

Name
Generic Dodecarotor cox geometry	Maintainer: William Peale develop707@gmail.com SYS_AUTOSTART = 24001

Helicopter

Common Outputs
MAIN1: main motor MAIN2: front swashplate servo MAIN3: right swashplate servo MAIN4: left swashplate servo MAIN5: tail-rotor servo

Name
Blade 130X	Maintainer: Bart Slinger bartslinger@gmail.com SYS_AUTOSTART = 16001

Hexarotor +

Common Outputs
MAIN1: motor1 MAIN2: motor2 MAIN3: motor3 MAIN4: motor4 MAIN5: motor5 MAIN6: motor6 AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Generic Hexarotor + geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 7001

Hexarotor Coaxial

Common Outputs

MAIN1: front right top, CW; angle:60; direction:CW MAIN2: front right bottom, CCW; angle:60; direction:CCW MAIN3: back top, CW; angle:180; direction:CW MAIN4: back bottom, CCW; angle:180; direction:CCW MAIN5: front left top, CW; angle:-60; direction:CW MAIN6: front left bottom, CCW;angle:-60; direction:CCW AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Generic Hexarotor coaxial geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 11001

Hexarotor x

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Generic Hexarotor x geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 6001

Octo Coax Wide

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 MAIN7: motor 7 MAIN8: motor 8

Name
Steadidrone MAVRIK	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 12002

Octorotor +

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 MAIN7: motor 7 MAIN8: motor 8 AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Generic Octocopter + geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 9001

Octorotor Coaxial

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 MAIN7: motor 7 MAIN8: motor 8

Name
Generic 10" Octo coaxial geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 12001

Octorotor x

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: motor 5 MAIN6: motor 6 MAIN7: motor 7 MAIN8: motor 8 AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Generic Octocopter X geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 8001

Quadrotor +

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel AUX4: feed-through of RC FLAPS channel

Name
Generic 10" Quad + geometry	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 5001

Quadrotor H

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel

Name
Reaper 500 Quad	Maintainer: Blankered SYS_AUTOSTART = 4040

Quadrotor Wide

Common Outputs
AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel AUX4: feed-through of RC FLAPS channel

Name
Team Blacksheep Discovery	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 10015 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel
3DR Iris Quadrotor	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 10016 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4
Steadidrone QU4D	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 10017 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel
Team Blacksheep Discovery Endurance	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 10018 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel

Quadrotor asymmetric

Common Outputs
MAIN1: motor1 (front right: CCW) MAIN2: motor2 (back left: CCW) MAIN3: motor3 (front left: CW) MAIN4: motor4 (back right: CW) MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel

Name
Spedix S250AQ	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4051

Quadrotor x

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: feed-through of RC AUX1 channel MAIN6: feed-through of RC AUX2 channel

<tr id=”copter_quadrotor_x_generic_quadrotor_x_with_mount(e.g.gimbal)”>




<tr id=”copter_quadrotor_x_lumenier_qav-r(raceblade)_5”_arms”>

Name
Generic Quadrotor x	Maintainer: Lorenz Meier lorenz@px4.io SYSAUTOSTART = 4001 Specific Outputs: AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel AUX4: feed-through of RC FLAPS channel
Generic Quadrotor x with mount (e.g. gimbal)	Maintainer: Leon Mueller SYS_AUTOSTART = 4002 Specific Outputs: AUX1: Mount pitch AUX2: Mount roll AUX3: Mount yaw AUX4: Mount retract
Lumenier QAV-R (raceblade) 5” arms	Maintainer: James Goppert james.goppert@gmail.com SYS_AUTOSTART = 4003
H4 680mm with Z1 Tiny2 Gimbal	Maintainer: Leon Mueller SYS_AUTOSTART = 4004
Lumenier QAV250	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4009
DJI Flame Wheel F330	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4010
DJI Flame Wheel F450	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4011
F450-sized quadrotor with CAN	Maintainer: Pavel Kirienko pavel.kirienko@gmail.com SYS_AUTOSTART = 4012
Parrot Bebop Frame	Maintainer: Michael Schaeuble SYS_AUTOSTART = 4013
Hobbyking Micro PCB	Maintainer: Thomas Gubler thomas@px4.io SYS_AUTOSTART = 4020
3DR Solo	Maintainer: Andreas Antener andreas@uaventure.com SYS_AUTOSTART = 4030
3DR DIY Quad	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4031
Generic 250 Racer	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 4050
DJI Matrice 100	Maintainer: James Goppert james.goppert@gmail.com SYS_AUTOSTART = 4060
Intel Aero Ready to Fly Drone	Maintainer: Lucas de Marchi SYS_AUTOSTART = 4070
ZMR250 Racer	Maintainer: Anton Matosov anton.matosov@gmail.com SYS_AUTOSTART = 4080
NanoMind 110 Quad	Maintainer: Henry Zhang zhanghui629@gmail.com SYS_AUTOSTART = 4090
Crazyflie 2.0	Maintainer: Dennis Shtatov densht@gmail.com SYS_AUTOSTART = 4900

Simulation (Copter)

Name
HIL Quadcopter X	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 1001

Tricopter Y+

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: yaw servo

Name
Generic Tricopter Y+ Geometry	Maintainer: Trent Lukaczyk aerialhedgehog@gmail.com SYS_AUTOSTART = 14001

Tricopter Y-

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: yaw servo

Name
Generic Tricopter Y- Geometry	Maintainer: Trent Lukaczyk aerialhedgehog@gmail.com SYS_AUTOSTART = 14002

Plane

Flying Wing

Common Outputs
MAIN1: left aileron MAIN2: right aileron MAIN4: throttle AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

<tr id=”plane_flying_wing_wing_wing(aka_z-84)_flying_wing”>

Name
Generic Flying Wing	SYSAUTOSTART = 3000
IO Camflyer	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 3030
Phantom FPV Flying Wing	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 3031
Skywalker X5 Flying Wing	Maintainer: Julian Oes julian@px4.io SYS_AUTOSTART = 3032
Wing Wing (aka Z-84) Flying Wing	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 3033
FX-79 Buffalo Flying Wing	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 3034
Viper	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 3035
Sparkle Tech Pigeon	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 3036
Modified Parrot Disco	Maintainer: Jan Liphardt JTLiphardt@gmail.com SYS_AUTOSTART = 3037
TBS Caipirinha	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 3100

Plane A-Tail

Common Outputs
MAIN1: aileron right MAIN2: aileron left MAIN3: v-tail right MAIN4: v-tail left MAIN5: throttle MAIN6: wheel MAIN7: flaps right MAIN8: flaps left AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Applied Aeronautics Albatross	Maintainer: Andreas Antener andreas@uaventure.com SYS_AUTOSTART = 2106

Simulation (Plane)

Common Outputs
MAIN1: aileron MAIN2: elevator MAIN3: rudder MAIN4: throttle MAIN5: flaps MAIN6: gear

Name
HILStar (XPlane)	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 1000

Standard Plane

Common Outputs
AUX1: feed-through of RC AUX1 channel AUX2: feed-through of RC AUX2 channel AUX3: feed-through of RC AUX3 channel

Name
Standard Plane	Maintainer: Lorenz Meier lorenz@px4.io SYS_AUTOSTART = 2100 Specific Outputs: MAIN1: aileron MAIN2: elevator MAIN3: throttle MAIN4: rudder MAIN5: flaps MAIN6: gear
Bormatec Maja	Maintainer: Andreas Antener andreas@uaventure.com SYS_AUTOSTART = 2105 Specific Outputs: MAIN1: aileron MAIN2: aileron MAIN3: elevator MAIN4: rudder MAIN5: throttle MAIN6: wheel MAIN7: flaps

Rover

Rover

Name
Generic Ground Vehicle	SYS_AUTOSTART = 50000 Specific Outputs: MAIN2: steering MAIN4: throttle
Axial Racing AX10	Maintainer: John Doe john@example.com SYS_AUTOSTART = 50001 Specific Outputs: MAIN1: pass-through of control group 0, channel 0 MAIN2: pass-through of control group 0, channel 1 MAIN3: pass-through of control group 0, channel 2 MAIN4: pass-through of control group 0, channel 3 MAIN5: pass-through of control group 0, channel 4 MAIN6: pass-through of control group 0, channel 5 MAIN7: pass-through of control group 0, channel 6 MAIN8: pass-through of control group 0, channel 7
Traxxas stampede vxl 2wd	Maintainer: Marco Zorzi SYS_AUTOSTART = 50002 Specific Outputs: MAIN2: steering MAIN4: throttle

Tool

custom

Name
Passthrough mode for Snapdragon	Maintainer: Julian Oes julian@oes.ch This startup can be used on Pixhawk/Pixfalcon/Pixracer for the passthrough of RC input and PWM output. SYS_AUTOSTART = 20000

VTOL

Standard VTOL

Name
Generic Quadplane VTOL	SYS_AUTOSTART = 13000 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 AUX1: Aileron 1 AUX2: Aileron 2 AUX3: Elevator AUX4: Rudder AUX5: Throttle
Fun Cub Quad VTOL	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 13005 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 AUX1: Aileron 1 AUX2: Aileron 2 AUX3: Elevator AUX4: Rudder AUX5: Throttle
Generic quad delta VTOL	Maintainer: Simon Wilks simon@uaventure.com SYS_AUTOSTART = 13006 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 AUX1: Right elevon AUX2: Left elevon AUX3: Motor
Generic AAVVT v-tail plane airframe with Quad VTOL.	Maintainer: Sander Smeets sander@droneslab.com SYS_AUTOSTART = 13007
QuadRanger	Maintainer: Sander Smeets sander@droneslab.com SYS_AUTOSTART = 13008
Sparkle Tech Ranger VTOL	Maintainer: Andreas Antener andreas@uaventure.com SYS_AUTOSTART = 13009
DeltaQuad	Maintainer: Sander Smeets sander@droneslab.com SYS_AUTOSTART = 13013 Specific Outputs: MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 3 MAIN4: motor 4 MAIN5: Right elevon MAIN6: Left elevon MAIN7: Pusher motor MAIN8: Pusher reverse channel

VTOL Duo Tailsitter

Common Outputs
MAIN1: motor right MAIN2: motor left MAIN5: elevon right MAIN6: elevon left

Name
Caipiroshka Duo Tailsitter	Maintainer: Roman Bapst roman@px4.io SYS_AUTOSTART = 13001

VTOL Quad Tailsitter

Common Outputs
MAIN1: motor 1 MAIN2: motor 2 MAIN3: motor 4 MAIN4: motor 5 MAIN5: elevon left MAIN6: elevon right MAIN7: canard surface MAIN8: rudder

<tr id=”vtol_vtol_quad_tailsitter_quadrotor+_tailsitter”>

Name
Quadrotor X Tailsitter	Maintainer: Roman Bapst roman@px4.io SYSAUTOSTART = 13003
Quadrotor + Tailsitter	Maintainer: Roman Bapst roman@px4.io SYS_AUTOSTART = 13004

VTOL Tiltrotor

Common Outputs
AUX1: Tilt servo AUX2: Elevon 1 AUX3: Elevon 2 AUX4: Gear

Name
BirdsEyeView Aerobotics FireFly6	Maintainer: Roman Bapst roman@uaventure.com SYS_AUTOSTART = 13002 Specific Outputs: MAIN1: Front right motor bottom MAIN2: Front right motor top MAIN3: Back motor bottom MAIN4: Back motor top MAIN5: Front left motor bottom MAIN6: Front left motor top
CruiseAder Claire	Maintainer: Samay Siga samay_s@icloud.com SYS_AUTOSTART = 13010
E-flite Convergence	Maintainer: Andreas Antener andreas@uaventure.com SYS_AUTOSTART = 13012 Specific Outputs: MAIN1: Motor right MAIN2: Motor left MAIN3: Motor back MAIN4: empty MAIN5: Tilt servo right MAIN6: Tilt servo left MAIN7: Elevon right MAIN8: Elevon left