Question

安装flannel网络插件

所有的node节点都需要安装网络插件才能让所有的Pod加入到同一个局域网中，本文是安装flannel网络插件的参考文档。

建议直接使用yum安装flanneld，除非对版本有特殊需求，默认安装的是0.7.1版本的flannel。

yum install -y flannel

service配置文件/usr/lib/systemd/system/flanneld.service。

[Unit]
Description=Flanneld overlay address etcd agent
After=network.target
After=network-online.target
Wants=network-online.target
After=etcd.service
Before=docker.service

[Service]
Type=notify
EnvironmentFile=/etc/sysconfig/flanneld
EnvironmentFile=-/etc/sysconfig/docker-network
ExecStart=/usr/bin/flanneld-start \
  -etcd-endpoints=${FLANNEL_ETCD_ENDPOINTS} \
  -etcd-prefix=${FLANNEL_ETCD_PREFIX} \
  $FLANNEL_OPTIONS
ExecStartPost=/usr/libexec/flannel/mk-docker-opts.sh -k DOCKER_NETWORK_OPTIONS -d /run/flannel/docker
Restart=on-failure

[Install]
WantedBy=multi-user.target
RequiredBy=docker.service

/etc/sysconfig/flanneld配置文件：

# Flanneld configuration options  

# etcd url location.  Point this to the server where etcd runs
FLANNEL_ETCD_ENDPOINTS="https://172.20.0.113:2379,https://172.20.0.114:2379,https://172.20.0.115:2379"

# etcd config key.  This is the configuration key that flannel queries
# For address range assignment
FLANNEL_ETCD_PREFIX="/kube-centos/network"

# Any additional options that you want to pass
FLANNEL_OPTIONS="-etcd-cafile=/etc/kubernetes/ssl/ca.pem -etcd-certfile=/etc/kubernetes/ssl/kubernetes.pem -etcd-keyfile=/etc/kubernetes/ssl/kubernetes-key.pem"

如果是多网卡（例如vagrant环境），则需要在FLANNEL_OPTIONS中增加指定的外网出口的网卡，例如-iface=eth2

在etcd中创建网络配置

执行下面的命令为docker分配IP地址段。

etcdctl --endpoints=https://172.20.0.113:2379,https://172.20.0.114:2379,https://172.20.0.115:2379 \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  mkdir /kube-centos/network
etcdctl --endpoints=https://172.20.0.113:2379,https://172.20.0.114:2379,https://172.20.0.115:2379 \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  mk /kube-centos/network/config '{"Network":"172.30.0.0/16","SubnetLen":24,"Backend":{"Type":"vxlan"}}'

如果你要使用host-gw模式，可以直接将vxlan改成host-gw即可。

注：参考网络和集群性能测试那节，最终我们使用的host-gw模式，关于flannel支持的backend模式见：https://github.com/coreos/flannel/blob/master/Documentation/backends.md。

启动flannel

systemctl daemon-reload
systemctl enable flanneld
systemctl start flanneld
systemctl status flanneld

现在查询etcd中的内容可以看到：

$etcdctl --endpoints=${ETCD_ENDPOINTS} \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  ls /kube-centos/network/subnets
/kube-centos/network/subnets/172.30.14.0-24
/kube-centos/network/subnets/172.30.38.0-24
/kube-centos/network/subnets/172.30.46.0-24

$etcdctl --endpoints=${ETCD_ENDPOINTS} \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  get /kube-centos/network/config
{ "Network": "172.30.0.0/16", "SubnetLen": 24, "Backend": { "Type": "vxlan" } }

$etcdctl --endpoints=${ETCD_ENDPOINTS} \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  get /kube-centos/network/subnets/172.30.14.0-24
{"PublicIP":"172.20.0.114","BackendType":"vxlan","BackendData":{"VtepMAC":"56:27:7d:1c:08:22"}}

$etcdctl --endpoints=${ETCD_ENDPOINTS} \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  get /kube-centos/network/subnets/172.30.38.0-24
{"PublicIP":"172.20.0.115","BackendType":"vxlan","BackendData":{"VtepMAC":"12:82:83:59:cf:b8"}}

$etcdctl --endpoints=${ETCD_ENDPOINTS} \
  --ca-file=/etc/kubernetes/ssl/ca.pem \
  --cert-file=/etc/kubernetes/ssl/kubernetes.pem \
  --key-file=/etc/kubernetes/ssl/kubernetes-key.pem \
  get /kube-centos/network/subnets/172.30.46.0-24
{"PublicIP":"172.20.0.113","BackendType":"vxlan","BackendData":{"VtepMAC":"e6:b2:fd:f6:66:96"}}

如果可以查看到以上内容证明flannel已经安装完成，下一步是在node节点上安装和配置docker、kubelet、kube-proxy等，请参考下一节部署node节点。