系统移植后遇到的奇怪问题

发布于 2022-07-24 08:51:12 字数 7697 浏览 14 评论 3

我在ARM9的板子上成功移植了vivi + linux-2.6.14.1 + yaffs文件系统,板子能正常启动,但是却不能运行我在Red Hat 9下交叉编译出来的任何应用程序,提示如下:
-sh: ./*****: not found
我用的交叉编译环境是3.4.4的
板子的启动信息如下:
VIVI version 0.1.4 (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release)) #0.1.4 Sat Sep 9 19:31:02 CST 2006
MMU table base address = 0x33F9C000
Succeed memory mapping.
+---------------------------------------------+
| S3C2410X USB Downloader ver R1.11 SEP/03/02 |
+---------------------------------------------+
FCLK=200MHz,DMA mode
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3
formAT: +++
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)
Found saved vivi parameters.
Press Return to start the LINUX/Wince now, any other key for vivi
Copy linux kernel from 0x001d0000 to 0x30008000, size = 0x00200000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock/5 init=/linuxrc console=ttySAC0,115200"
MACH_TYPE = 193
NOW, Booting Linux......
Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.14.1 (root@localhost.localdomain) (gcc version 3.4.4) #2 Thu Oct 12 07:34:11 CST 2006
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)

Machine: SMDK2410

ATAG_INITRD is deprecated; please update your bootloader.

Memory policy: ECC disabled, Data cache writeback

CPU S3C2410A (id 0x32410002)

S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz

S3C2410 Clocks, (c) 2004 Simtec Electronics

CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on

USB Control, (c) 2006 sbc2410

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets

CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets

Built 1 zonelists

Kernel command line: noinitrd root=/dev/mtdblock/5 init=/linuxrc console=ttySAC0,115200

irq: clearing subpending status 00000002

PID hash table entries: 512 (order: 9, 8192 bytes)

timer tcon=00000000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8

Console: colour dummy device 80x30

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 64MB = 64MB total

Memory: 61952KB available (2201K code, 558K data, 100K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

softlockup thread 0 started up.

NET: Registered protocol family 16

S3C2410: Initialising architecture

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics

DMA channel 0 at c4800000, irq 33

DMA channel 1 at c4800040, irq 34

DMA channel 2 at c4800080, irq 35

DMA channel 3 at c48000c0, irq 36

NetWinder Floating Point Emulator V0.97 (double precision)

devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

fuse init (API version 7.2)

yaffs Oct 12 2006 07:28:25 Installing.

Initializing Cryptographic API

Console: switching to colour frame buffer device 80x25

fb0: Virtual frame buffer device, using 1024K of video memory

S3C2410 RTC, (c) 2004 Simtec Electronics

s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410

s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410

s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

loop: loaded (max 8 devices)

usbcore: registered new driver ub

Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)

eth0: CS8900A rev E at 0xe0000300 irq=53, no eeprom , addr: 08: 0:3E:26:0A:5B

Linux video capture interface: v1.00

V4L-Driver for Vision CPiA based cameras v1.2.3

Since in-kernel colorspace conversion is not allowed, it is disabled by default now. Users should fix the applications in case they don't work without conversion reenabled by setting the 'colorspace_conv' module parameter to 1<6>USB driver for Vision CPiA based cameras v1.2.3

usbcore: registered new driver cpia

SCSI Media Changer driver v0.25

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2410-nand: mapped registers at c4980000

s3c2410-nand: timing: Tacls 10ns, Twrph0 40ns, Twrph1 10ns

NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)

NAND_ECC_NONE selected by board driver. This is not recommended !!

Scanning device for bad blocks

Creating 6 MTD partitions on "NAND 64MiB 3,3V 8-bit":

0x00000000-0x00020000 : "vivi"

0x00020000-0x00040000 : "eboot"

0x00040000-0x00050000 : "param"

0x00050000-0x001d0000 : "logo"

0x001d0000-0x003d0000 : "kernel"

0x003d0000-0x03ffc000 : "root"

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 2, 16384 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Root-NFS: No NFS server available, giving up.

VFS: Unable to mount root fs via NFS, trying floppy.

yaffs: dev is 32505861 name is "mtdblock5"

yaffs: Attempting MTD mount on 31.5, "mtdblock5"

VFS: Mounted root (yaffs filesystem).

Mounted devfs on /dev

Freeing init memory: 100K

init started:  BusyBox v1.1.3 (2006.10.11-23:55+0000) multi-call binary

Starti
Please press Enter to activate this console.

期待各位大牛的出现!小弟在线等

如果你对这篇内容有疑问,欢迎到本站社区发帖提问 参与讨论,获取更多帮助,或者扫码二维码加入 Web 技术交流群。

扫码二维码加入Web技术交流群

发布评论

需要 登录 才能够评论, 你可以免费 注册 一个本站的账号。

评论(3

你曾走过我的故事 2022-07-26 01:32:22

是跑起来了啊~~!可就是运行不了应用程序,为什么?

迷迭香的记忆 2022-07-25 18:41:19

你的 busybox 不是跑起来了吗?

美人迟暮 2022-07-24 14:46:49

为什么没人帮我啊??
有人遇到过这种情况吗?
难道是我见鬼了?

~没有更多了~
我们使用 Cookies 和其他技术来定制您的体验包括您的登录状态等。通过阅读我们的 隐私政策 了解更多相关信息。 单击 接受 或继续使用网站,即表示您同意使用 Cookies 和您的相关数据。
原文